@PMTeam@ZWO i did notice that after I set my asi2600mc pro gain to -25 in the camera tab page it swithes from Gain -25 to Gain 0 in the main asiair page (beside image resolution) as soon as I start imaging in preview mode and it also switches to Gain 0 when it starts imaging in autorun. Files are saved with detail info that says gain -25. When i go back to the main camera tab page to check, it changes back to -25 on the main page and it is at gain 0 on the camera tab page then slides to -25 immediately on the gain slider bar. I did send a bug report but not sure it will show up.

w7ay From my testing of 2.1.2,/ 10.92, I think MinMo of 0.2 is still in the software. My guiding was bad under this version with corrections only made in large increments when the guiding was past 1.2 on the guiding graph. I reverted back to the stable release and guiding improved and the frequency is more often and the size of the correction is more varied.

      charding i still think @PMTeam@ZWO needs to address this! Or at least make it an advanced fearure for all SWG mounts. That was my experience with the last beta test.

        ZWO can you please address this too high a Minmo of 0.2 for the SWG mounts.

        Just to confirm - is the ASIAIR still using JNOW for its coordinate system with the latest Public Beta?

        Or is it now using J2000?

          PMTeam@ZWO thank you for fixing the bug related to the incorrect display of -25 gain on the main page of Asiair for the asi2600mc pro cameras extended gain setting. That was super fast and it is confirmed fixed in the latest testflight of Asiair that I just ran.

            It could be very useful to be able to do ROI on the 2600. We have been asking for it for a long time. Thank you

            ppurbano first of all it puts the camera at unity gain but that has less meaning these days. The biggest gain is the extended full well capacity. It can be useful for very fast scopes in the range of f2 to f3.2 so the pixels do not get oversaturated. Therefore it it is possible to do less longer exposures instead of more shorter ones. Truthfully the tiny bit of dynamic range increase also may not outweigh the very rapid increase of read noise at gain -25 compared to gain 0. It is nice to have options, whether it is useful for most… probably not and gain 0 for broadband and gain 100 for broadband and narrowband will still be the most used gain settings.

                2.12 does not work with iOS 17.2, it loads and gets to the firmware update screen but the green update button is unclickable and you are stuck there. tried on two devices (iPad Pro & iPhone 15) and both fail to update or get past the screen.

                I reverted off beta to the current live version in App store and the firmware update worked fine from 10.71 to 10.74. so something is wrong with the beta's update screen/button/process.

                if you could please please address the silly start in landscape, switch to portrait, back to landscape modes.

                please pick one or allow both, but don't force people to switch back and forth and have to fumble with their device that's in a stand or on a table.

                  Guiding wasn't the best for me with the beta. I tried .2x guide rate which seemed to really smooth things out, but it wasn't making corrections soon enough. I hardly had any corrections in Dec and very few in Ra., Rms still over 1.

                    I can confirm that the Sony Alpha 6000 is now fully functional and no longer displays those colored dots. I appreciate your assistance! I was starting to lose hope and had considered selling it.
                    I couldn't try it at night bc of the weather these days. but my test in daylight was very pleasing.

                      Kevin_A I dont know how you could even check but it was pretty obvious minmo had been increased.

                        lenn1 Thanks for this! I may have to give my a6000 with ASIAIR a good run as well once the weather clears up 🙂

                            eokorie79 make sure that your battery is well charged or use a dummy battery