ASIAIR v2.2.2 has been released!: Page 6

ASIAIR v2.2.2 has been released!

deckblad

Excitedly hoping you release a firmware that works. Station mode doesn't work. Same as many others have said. I also can't figure out how to do a full reset of the ASIAIR Mini. I have yet to figure out how to make it forget current settings. It has my wifi password saved and I can't get it to reset.

I tried back loading 2.2.1 and 2.1.5. Those don't work either. They also don't clear the existing settings for the first station mode wifi AP I set up.

Swizerlan

w7ay looks like the rotator is coming. They should give it the ability to mechanically adjust tilt too

Swizerlan

DrJ it likely is, you need a usb ground loop isolator. They are less than $20

deckblad

I found the Android beta release site here.

https://www.pgyer.com/c40743d6504d85159f65829f6dfd4ae4

Unfortunately, the newest version 2.3_1025 still doesn't fully load when in Station mode.

I can see the device when scanning. But, the green dot circle spins forever with no results after clicking on connect.

I don't like that the alternative is to get the more expensive ASIAIR Pro to circumvent bad wifi support.

TomasK

Upgraded 2.2.1 to 2.3 yesterday
Shooting all night from about 9:30PM to 05:00AM
No issues at all - meridian flip ok, refocus on filters, guiding calibration after flip... all OK
Had saved targets so I had no time to play with Atlas changes - saw new rectangle there. But basic functionality is just fine in my case on iOS

StarMedic

TomasK where? Testflight still says 2.2.2 on my phone.

StarMedic

w7ay I only see 2.2.2 betas. How did you get 2.3 to show up?

StarMedic

DDivoAstro link? I only see 2.2.2 in TF

w7ay

Build 17 of ASIAIR Beta v2.3 just came out on iOS/iPad/macos TestFlight. Fixes that need to be tested now include these:

Chen

StarMedic

w7ay been testing. Still had issues with station mode just stopping working mid runs so something is still up with that. Using direct mode everything seems to be working ok.

johnpd

w7ay

I assume the "occasional DSO Stack crash" refers to Live Stacking. There was an issue that at times when you start stacking, no images are downloaded and no stacking takes place. You had to restart everything to get it working again.

JohnD

azskyguy

[unknown] Doesn't sound like the massive network errors have been fixed. From the notes it appears the corrupted frames from the 2600 MC Air are fixed, which would be great. When one of those frames appeared, it brought the entire automated process to a halt.

Lewisite

brazzo229 Thank you!!!

zwo2_jacky

Yesterday I was out and about with Asiair Plus and beta-firmware 2.3 (Android) + ASI2600MC Pro. Platesolving for polar alignment would not work, although 3000 stars were recognized. After a few attempts back to Preview and there Detect. Back to Polar Alignment and now the Platesolving worked.
In Preview, the scroll bar for the exposure time remained at 60 seconds and could not be changed to a longer time. In autorun mode, however, 300 seconds was also possible.
Otherwise the system worked. The meridian flip also worked perfectly.

Ali59

PMTeam@ZWO
The Firmware is still a problem
The following issues persist
The ASIAIR disconnects randomly for no reason
The sync to target in the sky Athlas is off.
There automatic copy of exposure of flats is gone!!
The guider sometimes stops working

I have contacted support with No help at all
I have returned already 1 ASIAIR plus and the new one still has the same issues

Please help
Thanks

Ali59

Why nobody from ZWO responds here?
I thought this was a support forum?

DDivoAstro

Ali59 Almost 6 weeks since the 2.2.2 release, no public update since, this is not acceptable.
I'm using beta 2.2.3 (iOS), which has solved all the problems of 2.2.2.
Although there are still pb with 2.2.3, the same known pb that existed before 2.2.2, such as random disconnections, they have not been resolved.
And no response from the ZWO team.
¿ Should we switch to Nina ?

« Previous Page