ASIAIR v2.1.2 has been released!: Page 6

ASIAIR v2.1.2 has been released!

Tech@ZWO

evilc did not move or plate solve failed?

evilc

Tech@ZWO Plate solve fine. Mount moved wrong direction then stops. Rebooting ASI solves issue for ONE goto.

Tech@ZWO

felixcortez
Only connect one device at one time to try, is there any difference?

In addition, Do these devices work on PC?

賴小熊

evilc https://www.pgyer.com/air_test
However, I don't know why ZWO provided two key verision, 2.1.4 and 2.2 at the same time,
2.1.4_0410(674) and 2.2_0410(673), which one is correct or the latest?? ( maybe for different ASIAIR)

bladezz

Also updated firmware on asiair plus now get images like below zwo eaf doesn't focus correctly and guidecam asi120mm view is awful. I have disconnected and reconnected cables reinstalled firmware update still same problems I have logged bug reports and clicked on the upload logs but in the below reports shows no logs so not sure if that is a bug or it never worked previously.

BT20240411184127A
BT20240411515288A
BT20240411818528A
BT20240411887908A

DavesView

bladezz
I haven't seen any focus issues on mine, but in the many reports of issues that I have seen on Astrobin and CN, the problems are far ranging with differences among the disgruntled users... me being one of those.

bladezz

nicolas this is what I have was previously 6020x4016 and now 4015 this firmware has killed my rig eaf was working now it says autofocus complete and get huge white blobs that should be small sharp stars

DavesView

I experienced problems after the upgrade from the very start. I have reverted back to 2.0 (10.46). So the remaining issues were when AA chooses a guide star, it always goes for the brightest star of the very few that show and the numbers peg out at 255. I have to drop the gain down to 7 in order for it to pick a star that isn't maxed out. The guide screen is very dark and very few stars show up. I normally set gain at medium 28, or high 48 and sometimes bump it up to 60, depending on seeing conditions. Don't pat yourselves on the back yet, this load is screwed up.

charding

There is a bug that needs to be addressed when multiple people (for example, at a star party) are using station mode with a common router at that location. Once you connect your ASIAir by station mode to the common router that others are using in station mode, then anyone of those other people can connect to your ASIAir. This has caused people to inadvertantly connect to the wrong ASIAir and take over control of it.

Neoprog

Hello there.
I've updated the firmware last night before shooting and I've troubles with my Nikon Z6 II camera.
In preview and plate solving I have a warning about RAW format (must clic on ok each time) and the pictures seemed to be a little bit strange (the moon wasn't really round).
So for the first clear night of the year, yes, I had to use directly my caemra without the Asiair Plus to shoot 12P Pons Brooks.
All the best
JC

bladezz

I have had a reply from zwo bug report and they confirm you should roll back to your previous firmware I have just done this and everything looks back to normal I get my 1 pixel back to 4016. To roll back for the asiair plus click on the i icon restore previous version once it is complete just close your app and uninstall it and install the previous version of the app that corresponds to the version that last worked for you. Open app it will ask you to update firmware to that version mine was 10.74 once this is updated you should be back to where you was before updating to the latest firmware. Hope this helps

Neoprog

bladezz thanks, I will try this afternoon.

Neoprog

bladezz I only can reset to 9.97 or use 11.01. I’m on iOS.

Neoprog

I can't use my Asiair to do plate solving or stacking with Nikon Z6 II. It was ok before latest firmware.
I received this message when I do plate solving and sometimes during preview.

Asiair Plus 2.1.2 (11.01)
Nikon Z6 II 1.62
iPad iOS 17.4.1

No way to return to last firmware, it's 9.97 (reset) or 11.01.

Can you help me ?

Thanks

bladezz

Neoprog this might be the version of asiair app you need to install for nikon support v2.0-10.23 once installed open it to connect to asiair after downgrade to 9.97 it will ask you to update to the same version of app.

bladezz

Do you have the previous ios app still in your downloads from when it worked all OK once you have restored to the 9.97 firmware you will need to find the app version you was on when it worked for you and Google that version for a download once you install the app and open it on ios it will ask you to update firmware to the same version of the app. I'm on Android so not sure what versions are available for ios. I suspect downloading from the store will give you the latest version again and back to square one with problems.

Neoprog

bladezz yes in Apple Store you can only download the latest version of the application.

bladezz

Neoprog yes you should be able find somewhere on the Internet with a download but you may have to sideload it on a ios and that's a whole different story that I don't know enough about. Google the version I sent you for ios and see if any results are found for a download and see if you can install it.

jeremie-zanone

@bladezz @nicolas @Neoprog

I'm a user of a Canon 1300D and I encountered the same behaviour, 1px is missing -> bayers matrice fucked up. I was not aware about this bug and lost 2 entire nights of shots with a clear sky.

With iOS you cannot just install an app like it is possible on Android, you have to install it from the official store or via TestFlight for beta version. I tried right now the beta in its version 2.1.4 tied to the firmware 11.0.5 and sadly the bug is still there. I also have opened an issue. I hope @ZWO will move their ass or create the possibility to have a rollback on firmware version.

Neoprog

jeremie-zanone Thanks for your lights. I'm Apple addict so no rollback exactly. I'm thinking of buying an Android terminal just to solve the problem. I've downloaded TestFlight but I don't know how to use this software yet. I going to find more infos about this soft.

Neoprog

Neoprog TestFlight version doesn't solve the RAW problem during the plate solving.

wvreeven

Neoprog Do you have a MacBook? I installed Android in a Parallels virtual machine which allows me to use whatever version of the ASIAir app. If you don't have a Parallels license, getting one may be cheaper that buying a tablet 😊

« Previous Page Next Page »