ASIAIR v2.4.2 has been released!: Page 16

ASIAIR v2.4.2 has been released!

azskyguy

Thanks.. I'm not sure I got anywhere... reset firmware to factory version... then ran 2.49. Scope said it needed to update firmware (again) and wound up with 41.63, which is where I was before I updated firmware. Meanwhile, Meridian flips are still dodgy.

azskyguy

PS.. running a ASIAIR 2600MC Air... (ASIAIR integrated with camera)

krakus56

Tomorrow I will receive a device to control my rigging and equipment. I am sorry to be leaving ASIair plus after several years, but after last night, when I had problems with the PA, I have had enough.
Goodbye, ASIair.

Corsair

krakus56
Or you could've asked for help by posting what your problem was and your equipment you're using.

Oh well. Hope the control system you've bought - whatever it is - works for you.

Let us know if you're going to get rid of your ASIAIR. One of us might want it.

Corsair

Luxo
The process for downgrading - at least from what I've seen - has always been to:
reset the ASIAIR first using the existing app,
then once the reset is done dont proceed with firmware update yet - just close the ASIAIR App,
uninstall the app from your device,
shutdown your device (not the ASIAIR),
turn your device back on,
install the version of the ASIAIR App you want,
reconnect your device to ASIAIR Wifi,
launch ASIAIR App,
proceed with firmware upgrade

I honestly do the above even when installing a firmware update.

krakus56

Corsair I have already tried installing an older version.
Every time I open it, I get an update message, which annoys me.
I have a lot of equipment from ZWO and it works well. Sometimes I find better prices, but I can't use them with ASIair.
That's what depresses me the most. I'm going back to N.I.N.A., which I used before.
At the moment, I'm not going to sell it. I have to learn N.I.N.A. all over again, and maybe then.
Best regards,

Corsair

krakus56
When you said you tried installing an older version did you (1) follow the right steps to downgrade both the firmware of the ASIAIR and the app version on your device AND (2) turn off auto update of the ASIAIR App on your device (you Android/Apple device controls this)?

Because from what you've said you didn't do step (2).

krakus56

Corsair nie będę już nic wykonywał, jutro konfiguruję urządzenie z win11 a asi idzie do szuflady, albo znajdzie nowego właściciela
Za dużo problemów od wersji 2.4, zniechęciłem się do ASIair

Corsair

krakus56
Well I haven't had any issues with 2.4.3 - 12.55 (App running on a Samsung Galaxy S22 Ultra running Android 15), HEQ5 Pro Mount, C8 SCT with f/6.3 Reducer, ASI294MC Pro camera cooled to 0°C doing unguided EAA (so Live Mode for Live Stacking).

This means good polar alignment is key for me since I only rely on mount tracking.

The ASIAIR is, relatively, a simple device which comes with limitations that you have to accept.

Considering you never posted on here what your issues were, what your equipment was, and the process you actually tried to follow to downgrade I'm not surprised by your outcome.

Hope it works out for you. It's a more complex path but does allow for more configurations and customisation.

AstroDude42

Haven’t seen any announcement here on this forum, neither about beta nor final release… ASIAir iOS app v2.4.4 has been released.

o7F3a3tb

AstroDude42
which camera is the ASI4400 MC PRO ?

chrisrose98

AstroDude42 It is a little unfortunate that ZWO left the word "beta" next to the Logo when you launch the app. It's on the screen where you hit "enter device".

AstroDude42

o7F3a3tb sorry, can‘t help here. Please ask the ZWO guys.

Easylink

[unknown] Seems to be a typo. The 2400 is probably meant. Curious about the “Fixed known bugs”

1WeD8U9y

If ASIAIR firmware retrodated to v. 2.3.3. Will other accessories, like EAF, also need to be retrodated?

Luxo

1WeD8U9y

EAF, CAA and filter wheel, no. CAA was the last accessory added before 2.3.3.
EAF works fine (I have two scopes fitted with these).
CAA works but I disable it because I don't want it doing unwanted rotations.

See ASIAir: the Missing Manual, chapter 24 for instructions on how to revert to 2.3.3, permanently.
https://www.icloud.com/iclouddrive/010wWOevZeXCOc79pGNNBWV9Q#ASIAir_Missing_Manual_0.8

Lots of users on CN are beginning to report problems but are ignorant of the mess ZWO have created.

Q3TOBAP2

PMTeam@ZWO After forced update of asi air mini and the app, plate solve does not work and asi is moving the mount all over the place , tried to reverse the firmware update but as soon as it restarted it forced the update again. After about 4 hours of fucking around with it I give up, lost whole night of imaging!!! Now I have $3000 worth of red paper weights!!!

Vincent195

Nobody have seen this ?

Gatsu87

Vincent195 Unfortunately, it's been over a month since anyone from the zwo staff has responded to this thread.

Sonixx

Gatsu87

Unfortunately this thread got very messy. Lots of claims that things are not working. Most of these claims crumbled to dust when you ask for details.

If you experience real problems, it should be brought forward in a friendly manner with sufficient information and the number of the bug report sent. Otherwise it becomes pointless and it muddies the waters.

Hopefully the community and the ZWO team can leave this behind and start fresh.

Best regards,

Stephan

Corsair

I decided to make a new thread to discuss v2.4.4 ago/ firmware release here:
https://bbs.zwoastro.com/d/25293-unannounced-asiair-v244

« Previous Page Next Page »